FE: Instrumentation & Controls (NCEES FE — Instrumentation & Controls (topic practice)) — Free Online Mock Test

  • FE topic practice
  • Instrumentation & Controls
  • on the official NCEES Fundamentals of Engineering knowledge areas.
  • Official language: English.
  • Official language: English.
Advanced United States Engineering Licensure 18 questions 27 min 50 distinct variants
Start free practice test →

FE: Instrumentation & Controls exam at a glance

18
Questions
27
Minutes total
1
Section
50
Variants

50 full-length mock tests

Attempt 50 full-length mocks

Each is a distinct question set built on the real 18-question, 27-minute pattern, with instant scoring and section-wise analysis. The first is free; unlock all 50 forever for $1.99 (one-time, no subscription).

FreeUnlock for $1.99
Unlock all 50 FE: Instrumentation & Controls tests — $1.99 Start free mock →

FE: Instrumentation & Controls key facts & eligibility

FE: Instrumentation & Controls at a glance — verified exam facts
Conducting bodyNCEES (National Council of Examiners for Engineering and Surveying)
Official websitencees.org ↗
ModeFocused practice on the Instrumentation and Controls knowledge area of the NCEES FE exam. It is a topic on the mechanical, chemical, other-disciplines and related FE discipline versions, answered using the searchable electronic FE Reference Handbook.
FrequencyThe FE exam is offered year-round at Pearson VUE test centres.
Scoring & markingOn the FE, this area covers measurement (sensors and instrumentation, error and calibration), control-system fundamentals (block diagrams and transfer functions, open- and closed-loop response), and basic system stability — all supported by the FE Reference Handbook.
LanguageEnglish.

Who is eligible for FE: Instrumentation & Controls?

For candidates preparing for an FE discipline exam that includes instrumentation and controls.

Last verified July 2026 against NCEES — FE Exam. Always confirm current details on the official website before you register.

FE: Instrumentation & Controls section breakdown

The FE: Instrumentation & Controls mock test on Wrexa Edge replicates the real exam's section structure — same names, same question count per section, same time limits. No inter-section breaks — the timer runs continuously.

  • FE: Instrumentation & Controls (18 Q)

Marking scheme

+1 per correct. Try your score.

+1Correct
0Wrong
0Unanswered
Your score0/ 1000

Strategy: FE: Instrumentation & Controls has no negative marking. Attempt every question — blank answers cost you potential marks but cannot pull your score down.

Scale: FE: Instrumentation & Controls (pass 700/1000).

How FE: Instrumentation & Controls is conducted

  • Mode
  • Test format
  • Backtracking
  • Mark for review

FE: Instrumentation & Controls time strategy

With 18 questions in 27 minutes, you have about 90 seconds per question on average. Successful candidates aim for the following pacing on each section:

  • FE: Instrumentation & Controls (18 Q)

Wrexa Edge's analytics show your actual time-per-question after every mock so you can spot which sections you're losing time on.

FE: Instrumentation & Controls topics covered

Across the 50 Wrexa Edge variants of FE: Instrumentation & Controls, the following topics appear most often (sample distribution from one variant):

FE: Instrumentation & Controls (18 Q)

  • Instrumentation & Controls · 8
  • Control — Stability · 2
  • Signals — Fourier · 1
  • Signals — LTI · 1
  • Signals — Sampling · 1
  • Signals — Convolution · 1
  • Signals — Z-Transform · 1
  • Control — Transfer Function · 1

FE: Instrumentation & Controls difficulty calibration

Advanced tier. Advanced-level: high-stakes exam with rigorous content depth. Expect 4-8 months of structured prep.

FE topic practice · Instrumentation & Controls · on the official NCEES Fundamentals of Engineering knowledge areas. Official language: English. · Official language: English.

Verified content — Wrexa Edge's FE: Instrumentation & Controls bank has been deeply curated with real exam-aligned content (estimated 100% syllabus coverage).

How Wrexa Edge prepares you for FE: Instrumentation & Controls

  • Real test-day interface
  • 50 distinct variants
  • Detailed analytics
  • Spaced repetition (Notebook)
  • Optional proctoring
  • Free to start

Expert take: what FE: Instrumentation & Controls really tests

Instrumentation and Controls is a knowledge area on the mechanical, chemical, other-disciplines and related NCEES FE exams, answered using the FE Reference Handbook. It covers measurement (sensors, error and calibration), control-system fundamentals (block diagrams and transfer functions, open- and closed-loop response) and basic stability.

Preparation tips

  • Practise block-diagram reduction and transfer functions.
  • Understand open- vs closed-loop response and feedback.
  • Know common sensors and sources of measurement error.

Common mistakes to avoid

  • Errors reducing block diagrams or handling feedback signs.
  • Confusing open-loop and closed-loop behaviour.

FE: Instrumentation & Controls study plan

A phase-by-phase roadmap from your first concept to test-ready. Stretch or compress each phase to fit the time you have before your attempt.

1 Phase 1 — Measurement Week 1
  • Sensors, instrumentation and calibration
  • Measurement error
  • Handbook content location
2 Phase 2 — Control systems Week 2
  • Block diagrams and transfer functions
  • Open/closed-loop response and stability
  • Timed problem drills
3 Phase 3 — Speed Final days
  • Fast Handbook lookups
  • Mixed FE controls sets
  • Accuracy under time

Where FE: Instrumentation & Controls can take you

A strong FE: Instrumentation & Controls result opens up these careers and higher-study paths:

  • FE topic
  • Automation base
  • Handbook fluency
  • Toward PE

Best books & official prep for FE: Instrumentation & Controls

  • FE Reference Handbook — Instrumentation & Controls section — NCEES
  • FE controls review problems — Various

Official practice: Practise measurement/error, block-diagram reduction, transfer functions and system response using the FE Reference Handbook.

Previous-year papers: Practise with the instrumentation-and-controls questions in the official NCEES FE practice exams.

Sample FE: Instrumentation & Controls practice questions

5 questions taken from the FE: Instrumentation & Controls mock tests on Wrexa Edge. Try each one, then reveal the answer.

  1. Q1. A strain gauge measures strain by detecting a change in its:

    1. Temperature
    2. Light output
    3. Flow rate
    4. Electrical resistance
    Show answer

    Answer: D — Electrical resistance

  2. Q2. Sampling a continuous signal must satisfy the:

    1. Nyquist criterion (fs ≥ 2·f_max)
    2. Ohm’s law
    3. Bernoulli equation
    4. Fourier’s law
    Show answer

    Answer: A — Nyquist criterion (fs ≥ 2·f_max)

  3. Q3. Aliasing occurs when the sampling rate is:

    1. Too high
    2. Too low (below the Nyquist rate)
    3. Exactly the Nyquist rate
    4. Irrelevant
    Show answer

    Answer: B — Too low (below the Nyquist rate)

  4. Q4. Negative feedback in a control system generally:

    1. Increases gain without limit
    2. Always causes instability
    3. Improves stability and reduces sensitivity
    4. Removes the output
    Show answer

    Answer: C — Improves stability and reduces sensitivity

  5. Q5. A first-order system’s response is characterized by its:

    1. Damping ratio only
    2. Natural frequency only
    3. Pole pair
    4. Time constant (τ)
    Show answer

    Answer: D — Time constant (τ)

Frequently asked questions

What is the FE: Instrumentation & Controls exam pattern?
NCEES FE — Instrumentation & Controls (topic practice) contains 18 questions across 1 section: FE: Instrumentation & Controls (18 Q). Total duration is 27 minutes (about 90 seconds per question).
Does FE: Instrumentation & Controls have negative marking?
No — FE: Instrumentation & Controls has no negative marking. Each correct answer is worth 1 mark, so attempt every question.
How is FE: Instrumentation & Controls scored?
Scaled score range: 100 to 1000. FE: Instrumentation & Controls (pass 700/1000).
How can I practise FE: Instrumentation & Controls online for free?
Wrexa Edge gives you a free full-length FE: Instrumentation & Controls mock test — with instant scoring, detailed explanations and analytics — plus 49 more with a one-time $1.99 unlock that never expires. Start practising in under a minute, no card required.
What is the difficulty level of FE: Instrumentation & Controls?
FE: Instrumentation & Controls is rated Advanced difficulty on Wrexa Edge. Advanced-level: high-stakes exam with rigorous content depth. Expect 4-8 months of structured prep. FE topic practice · Instrumentation & Controls · on the official NCEES Fundamentals of Engineering knowledge areas. Official language: English. · Official language: English.
How long is the FE: Instrumentation & Controls exam?
FE: Instrumentation & Controls runs for 27 minutes total. On Wrexa Edge the timer is enforced exactly as on the real exam — including no inter-section breaks.
What topics are covered in FE: Instrumentation & Controls?
FE: Instrumentation & Controls is split into: FE: Instrumentation & Controls (18 Q). Each section is timed and weighted separately. FE topic practice · Instrumentation & Controls · on the official NCEES Fundamentals of Engineering knowledge areas. Official language: English. · Official language: English.
What tools or aids are allowed during FE: Instrumentation & Controls?
No special tools are required. Note: real exam is proctored — Wrexa Edge mirrors this with a webcam-based proctoring flow you can enable.
Is the FE: Instrumentation & Controls test adaptive?
No — FE: Instrumentation & Controls is a fixed-form (linear) test. Every candidate sees the same number of questions per section.
How many FE: Instrumentation & Controls mock tests does Wrexa Edge offer?
Wrexa Edge generates 50 distinct FE: Instrumentation & Controls variants — each with different question content, not just shuffled options — the first one free for everyone and 49 more with a one-time $1.99 unlock. That's 900 unique practice questions in the real test-day interface.
Is there a free FE: Instrumentation & Controls test series 2026?
Yes. The Wrexa Edge FE: Instrumentation & Controls test series for 2026 gives you a free full-length mock test (50 in total) plus subject-wise and topic-wise tests — instant scoring and detailed analysis, no card required.
Are FE: Instrumentation & Controls previous year question–style papers included?
Every FE: Instrumentation & Controls mock is modelled on the official exam pattern and the style of previous years' papers — the same 18-question structure, sections and marking — so your practice mirrors the real paper you'll sit.
Which is the best free FE: Instrumentation & Controls mock test online?
Wrexa Edge's FE: Instrumentation & Controls mock test replicates the real exam interface, timing and marking scheme, with instant score, section-wise analysis and 50 fresh variants — a strong free choice for 2026 preparation.
Can I take the FE: Instrumentation & Controls mock test on mobile?
Yes. FE: Instrumentation & Controls mock tests run in any browser on mobile, tablet or desktop — no app or download needed. Start on your phone and your progress and analytics sync when you sign in.
What is the FE: Instrumentation & Controls syllabus?
The FE: Instrumentation & Controls syllabus maps to its 1 section: FE: Instrumentation & Controls (18 Q). Wrexa Edge's mock tests cover the complete syllabus topic by topic — see the topics-covered breakdown above — so you practise every area at real exam difficulty.
What is the eligibility for FE: Instrumentation & Controls?
For candidates preparing for an FE discipline exam that includes instrumentation and controls. Wrexa Edge focuses on realistic FE: Instrumentation & Controls practice: a free full-length mock in the exact exam pattern, ready whenever you are.
When is the FE: Instrumentation & Controls exam and how should I prepare?
Official FE: Instrumentation & Controls exam dates are announced by the conducting body for each cycle — check the latest notification for the current schedule. To be ready, follow a phased study plan and take full-length timed mocks; Wrexa Edge gives you a free FE: Instrumentation & Controls mock with instant scoring so you can track your readiness week by week.

Related exams & practice tests

Candidates preparing for FE: Instrumentation & Controls also practise these on Wrexa Edge:

Browse more: All Engineering Licensure exams →  ·  All United States exams →  ·  Full exam catalog →

Ready to ace FE: Instrumentation & Controls?

Join thousands of candidates practising on Wrexa Edge. Free signup, 50 variants per exam, instant scoring.

Start practising free →
Wrexa Edge Mock Tests and Exams app icon
Wrexa Edge — Mock Tests & ExamsAvailable
Practise on the go — 1,900+ exams with the real interface, timer & marking. 1 free mock each.
Get it onGoogle Play
Wrexa Edge Mock Tests and Exams app icon
Get the Wrexa Edge app
Practise on your phone · free to start
Google Play